electrolux dishwasher problem solving

Electrolux Dishwashers Problems: 7 Common Issues (Must Read)

Electrolux dishwashers, like all Electrolux appliances, are high-quality and long-lasting.

Please enable JavaScript

Based on our research here are the 7 most common problems with Electrolux dishwashers

Electrolux Dishwasher Not Cleaning Properly

If your Electrolux dishwasher isn’t cleaning your dishes, the spray arm could be clogged, the soap dispenser could be broken, you’re using low-quality detergent, or the inlet valve could be defective or damaged.

Possible Solution(s):

Low-grade detergent, dirty filter, inlet valve, electrolux dishwasher not draining.

Is your dishwasher completely empty, or is there always an inch of water in the bottom?

Before you call a repair service, try these three simple fixes if your dishwasher won’t drain.

Dirty Filters

Blocked drain hose, blocked or faulty drain pump.

If you are unsure about any of these tasks or do not want to risk voiding your appliance’s warranty, contact a qualified plumbing technician to repair your dishwasher.

Electrolux Dishwasher Leaking

Electrolux dishwasher leaking from the bottom is usually caused by using the incorrect type and quantity of detergent, a clogged filter, overloading the machine, leaking detergent draws, or leaking hoses.

Damaged Door Seal

Incorrectly stacked dishwasher, blocked, loose, or damaged connecting hose, electrolux dishwasher buttons not working.

If the buttons on your Electrolux dishwasher are not working, the display may be defective or power supply issue.

Electrolux Dishwasher Lights Flashing or Blinking

The heating element is responsible for warming up the water to an optimum temperature.

Another reason can be a technical fault with the control panel that causes the circuitry to go haywire.

Electrolux Dishwasher Won’t Start

If the switch is faulty, the control board will not receive the signal, and the machine will not turn on.

However, before you call your local technician, try the troubleshooting steps listed below.

Check Power Supply

There are several possibilities here.

If you have troubleshot the items above and your dishwasher is still not working, might be faced with a faulty control board, drive motor, or Thermal Fuse.

Electrolux Dishwasher Stopping Mid Cycle

Then when you try to start the cycle again and get no response or find that the same mid-cycle premature end happens all over again,

The reason for your Electrolux dishwasher stopping mid-cycle is likely caused by a faulty door switch, blown fuse, or faulty control board. 

If you are uncomfortable about resolving this problem or do not want to risk voiding your appliance’s warranty, contact a qualified technician to repair your dishwasher.

Electrolux Dishwasher Making Noise

Strange noises coming from the dishwasher are not uncommon. They are usually nothing to be concerned about, and the noise problem is often easily resolved.

If the noise persists, it is best to contact a technician.

Electrolux Dishwasher Not Heating Water 

If you need an affordable, well-designed sleek looking dishwasher Electrolux is the brand to go with.

So, keep them in mind at all times and your Electrolux dishwasher will be in good working order.

Related Articles

Image by wayhomestudio on Freepik

Electrolux Dishwasher Resetting Made Easy: Step-by-Step Guide to Solve Common Issues

What To Know

• What is the difference between a power cycle and a reset.
• A power cycle involves turning the dishwasher off and back on, while a reset typically involves pressing a specific button or code combination.
• Yes, resetting the dishwasher yourself is generally safe, but always follow the instructions carefully and disconnect the power before performing any maintenance.

Electrolux dishwashers are renowned for their efficiency and reliability. However, like any appliance, they may occasionally encounter minor glitches or require maintenance. One of the most common solutions to resolve these issues is to reset the dishwasher. This blog post will provide a comprehensive guide on how to reset Electrolux dishwashers, covering various models and troubleshooting scenarios.

Why Reset an Electrolux Dishwasher?

There are several reasons why you may need to reset your Electrolux dishwasher:

• Error messages: The dishwasher may display error codes or messages indicating a malfunction.
• Malfunctioning cycles: The dishwasher may not complete cycles properly, leaving dishes dirty or wet.
• Drainage issues: The dishwasher may not drain water effectively, resulting in standing water or leaks.
• Power outages: A power outage can disrupt the dishwasher’s electronic controls.
• Routine maintenance: Regularly resetting the dishwasher can help maintain its optimal performance.

Steps to Reset Electrolux Dishwashers

The reset process may vary slightly depending on your Electrolux dishwasher model . Follow these steps for most models:

1. Power Cycle the Dishwasher

• Turn off the dishwasher at the circuit breaker or fuse box.
• Wait for 30 seconds.
• Turn the dishwasher back on.

2. Reset Button Method (for some models)

• Open the dishwasher door.
• Locate the reset button, usually near the control panel.
• Press and hold the reset button for 5 seconds.

3. Cancel Button Method (for some models)

• Press and hold the cancel button for 5 seconds.

4. Code Reset Method (for some models)

• Press the cycle selection button repeatedly until the display shows a code (e.g., “01”).
• Press and hold the start/resume button for 5 seconds.

Troubleshooting Common Dishwasher Issues

Error code e10.

• Cause: Water supply issue
• Solution: Check the water supply and ensure the water valve is open.

Error Code E20

• Cause: Drainage issue
• Solution: Clear any blockages in the drain hose or filter.

Error Code E30

• Cause: Temperature sensor malfunction
• Solution: Contact an authorized Electrolux service technician.

Error Code E40

• Cause: Overfill issue
• Solution: Check the float switch and ensure it is not stuck.

Error Code E50

• Cause: Heating element malfunction

Maintenance Tips for Electrolux Dishwashers

• Clean the filter regularly: Remove the dishwasher filter and clean it with warm soapy water.
• Check the drain hose: Inspect the drain hose for kinks or blockages.
• Use rinse aid: Rinse aid helps prevent water spots and improves drying performance.
• Run a cleaning cycle periodically: Use a dishwasher cleaner to remove mineral deposits and buildup.
• Avoid overloading the dishwasher: Overloading can prevent dishes from getting clean and can strain the dishwasher’s motor.

Summary: Resetting Your Electrolux Dishwasher for Optimal Performance

Resetting your Electrolux dishwasher is a simple yet effective way to resolve minor issues and maintain its optimal performance. By following the steps outlined in this guide, you can troubleshoot common dishwasher problems and restore your appliance to proper working order . Remember to perform regular maintenance to ensure your Electrolux dishwasher continues to provide years of reliable service.

Quick Answers to Your FAQs

Q: how often should i reset my electrolux dishwasher.

• A: Reset the dishwasher as needed when experiencing issues or as part of routine maintenance.

Q: What is the difference between a power cycle and a reset?

• A: A power cycle involves turning the dishwasher off and back on, while a reset typically involves pressing a specific button or code combination.

Q: Can I reset my Electrolux dishwasher if it is not draining?

• A: Yes, try resetting the dishwasher first. If the issue persists, check the drain hose and filter for blockages.

Q: What if the reset does not resolve the issue?

• A: If the reset does not fix the problem, contact an authorized Electrolux service technician for further assistance.

Q: Is it safe to reset my Electrolux dishwasher myself?

• A: Yes, resetting the dishwasher yourself is generally safe, but always follow the instructions carefully and disconnect the power before performing any maintenance.

Popular Posts:

Leave a Reply / Feedback Cancel reply

Your email address will not be published. Required fields are marked *

Save my name, email, and website in this browser for the next time I comment.

Find Out More

Is dishwasher insulation necessary unveiling energy efficiency secrets for modern kitchens, unveil the mystery: why is your dishwasher devastating your dinnerware, dishwasher maintenance made easy: learn the secrets of rinsing dishwasher aid and extending dishwasher life, dishwasher vs. fridge: the ultimate kitchen space saver, is dishwasher salt a hidden culinary gem the surprising answer, kitchenaid dishwasher warranty: the ultimate guide to protection and peace of mind.

How To Fix It

Common Electrolux Dishwasher Error Codes and Solutions

Like any appliance, your Electrolux dishwasher should operate seamlessly in the kitchen.

However, it’s not uncommon for owners of these machines to experience Electrolux dishwasher error codes every once in a while.

The reason for codes and solutions, however, are going to vary from case to case, and based upon the manufacturer’s model that you own.

Understanding the proper approach to fixing the common Electrolux dishwasher error codes not only prevents future issues, but also reduces the chances that you’ll have to hire a professional (and overpay) to do repair work in the future.

Most Common Codes

Table of Contents

Again, every dishwasher is a little different than the next. But, common Electrolux dishwasher error codes are typically related to overflow, too many/too few dishes in the dishwasher (imbalance), or clogged/backed up hoses and piping.

These are a few of the most common errors Electrolux dishwasher owners experience.

Bear in mind, that with each of these common Electrolux dishwasher error codes, the numbers may vary a bit, depending on the model (for example, IC0 might be IC1, IC2, or IC3, depending on your model).

However, the beginning of the codes tends to be similar, regardless of which model dishwasher you own, so this guide will at least provide some insight as to what the codes mean.

#iC0 (Electronic Control System)

This error code means a problem has been detected with the electronic control system. This typically affects freestanding or integrated machines.

One of the primary reasons you’ll see this code, indicating a potential problem with the control system, is a communication error .

The error might be between the control board and the rest of the parts in the dishwasher. This is preventing your dishwasher from starting.

Connect with an Appliance Repair Tech

Click here to use the chatbox to speak with one of our technicians. No in-home service calls. No appointments.

#i20, i40, iFO (Drain System)

This error means you’re dealing with clogged filters , or there’s a restricted drain line, which your dishwasher has detected.

If there’s a blockage in the drain line of your dishwasher’s system, this error will pop up.

Additionally, if your dishwasher’s drain pump is clogged, this might also trigger the i20, i40, or IFO error code to pop up on the control panel.

#i30 (Leak/Overflow)

With this error code, your dishwasher is informing you of a leak or water overflow, that is sitting in the drip pan (the base) of your dishwasher.

The code triggers that there is a leak or overflow coming from somewhere in your dishwasher (the code might vary for each model, based upon where the leak or overflow originates).

With this error, you’ll have to do a little more digging, since the leak can be coming from multiple areas in the machine.

#Er-03 (Motor Issue)

When your Electrolux machine’s motor is malfunctioning, this is the error code that will pop up on the control panel. This code will only come up in one of two instances.

First, the motor has failed. The second reason, is if the motor is being obstructed by dishes, or something else, while the motor is in operation.

Sometimes it’s as easy as removing the dish/obstruction, in other cases, repair might be necessary.

LOC (Dishwasher Lock Error)

This final common Electrolux dishwasher error codes appears if there is an issue with the door lock function (malfunction) with your Electrolux dishwasher unit.

If the door locks and won’t open, you’ll see this code. The only way to run a wash cycle is to first unlock the door.

The Solution to Electrolux dishwasher error codes

Again, every code error has a different solution. Make sure to check your manual if these solutions don’t work, however, for most systems, this should resolve the problem.

A simple solution is to press the power button; alternatively you can turn the power off at the breaker box for five minutes.

This will likely clear the error code, at which point you can restart the dishwasher.

Alternatively, you can try unplugging the dishwasher for 10 seconds to 1-minute and plugging it back in.

If it runs, it’s likely just a glitch that triggered the code. If not, this might indicate you need to replace the control panel.

If these solutions don’t work, you might have to contact a service technician to replace or repair the current control board.

#i20, i40, iFO

To repair this issue, you will

• Check and clean filters
• Clean the sump area
• Check for pinched, kinked, or blocked hoses
• Check to see the plug hasn’t been knocked out (if connected to a disposer)

Further inspect drain lines, hoses, drain pumps, and pressure switches. Clean all parts as necessary to remove blockage or obstructions.

You’ll first look for loose connections at the water inlet valve to ensure the unit is properly leveled when you see this error.

Look for potential leaks in the water fill valve and inspect the drain pump for blocks or clogging. If parts are damaged, rusted, or otherwise defective, they’ll have to be replaced.

Conduct an inspection of the wash motor wiring and also inspect the motor. Look for blockages. If nothing appears defective, replace the wash motor in your dishwasher.

If it has to be replaced, this is a job you’ll want to call a licensed Electrolux repair technician to perform for you.

With this final error, you’ll want to start by pressing/holding the AIR button for a minimum of 3 to 5 seconds while the door is latched shut.

With most lock issues, this will unhinge the door and pop it open.

At this point, you can restart/reselect your wash cycle. If it doesn’t unlatch the door, there might be a blockage or obstruction or something broke/jammed in the hinge.

Don’t attempt to force it open. Again, this might require a call to a professional technician in the event a part/replacement is necessary in some cases.

Regardless of the Electrolux dishwasher error codes you’re seeing, don’t fret.

Don’t immediately call a repair technician, who will open up your machine, and charge you an absurd amount of money, especially when they know it’s often as easy as unplugging and plugging the machine back in.

Try these resolutions first. If they don’t remedy the problem, check the manual for your specific dishwasher model.

If, at this point, the error persists, consider calling Electrolux to find a licensed repair technician in your area.

Reader Comments (2)

What is a “do” error code

I do not see where the “codes” are supposed to be visable? and my start screen looks like the one shown above? My machine runs for about 5 minutes then all lights flash in unison..and it stops?

Leave a Comment Cancel reply

Save my name, email, and website in this browser for the next time I comment.

This site uses Akismet to reduce spam. Learn how your comment data is processed .

Customer Support 6 days a week

• Chat with a Pro
• Call or text 1-877-477-7278
• Repair Forum
• Order Status

• Shop for Parts
• Get Repair Help

• Dishwasher Parts
• Dryer Parts
• Microwave Parts
• Range & Oven Parts
• Refrigerator Parts
• Washer Parts
• All Appliance Parts

Fix Your Electrolux Dishwasher: Common Electrolux Dishwasher Problems & Solutions

Having trouble with your Electrolux dishwasher not cleaning properly, showing error codes, leaking water, making unusual noises or failing to start or complete cycles? Don't call a technician yet, our DIY troubleshooting tips can help you accurately identify issues and handle basic Electrolux dishwasher repairs yourself in no time. Whether it's soap residue left on dishes, annoying grinding noises, broken spray arms, unexpected pooling of water on the floor, or failure to effectively wash the dishes, we provide the knowledge you need to diagnose the specific problem and fix many common issues. Learn what's causing your Electrolux dishwasher woes based on the symptoms, then gain the skills to get your appliance washing dishes sparkling clean again. Additionally, check our inventory for OEM replacement Electrolux dishwasher parts if you find the issue requires a replacement

Electrolux Dishwasher buttons not working

Electrolux Dishwasher dispenser not dispensing soap

Electrolux Dishwasher has a burning smell

Electrolux Dishwasher leaking

Electrolux Dishwasher leaking from motor area

Electrolux Dishwasher lights flashing or blinking

Electrolux Dishwasher making noise

Electrolux Dishwasher not cleaning

Electrolux Dishwasher not draining

Electrolux Dishwasher not drying dishes

Electrolux Dishwasher overflowing

Electrolux Dishwasher stops mid-cycle

Electrolux Dishwasher won't fill

Electrolux Dishwasher won't latch

Electrolux Dishwasher won't start

• Dehumidifier
• Garbage disposal
• Oven / Microwave Combo
• Range vent hood
• Ranges / Stove / Oven
• Refrigerator
• Trash compactor
• Washer Dryer Combo
• Hedge trimmer
• Leaf blower
• Log splitter
• Pole pruner
• Pressure washer
• Small engine
• String trimmer
• Wood chipper
• Fault Codes
• Kitchen Aid
• Sears / Kenmore

We are here to help you!

Connecting with agent . . .

Please introduce yourself to start live chat

Thank you for chatting with us. We are always happy to help you!

Are you sure you want to leave the chat? Connection with the agent will be lost

Do you want to continue chat or start new sesson?

• Smart Home Devices
• Voice Assistants
• Video Doorbells

Guide to Fixing Electrolux Dishwasher Error Codes

Table of Contents

Understanding Electrolux Dishwasher Error Codes

If you’re experiencing errors with your Electrolux dishwasher, don’t panic! Understanding Electrolux dishwasher error codes can help you diagnose the issue and get back to a sparkling clean kitchen in no time. In this section, we’ll explore the causes of Electrolux dishwasher error codes, so you can troubleshoot and fix the issue quickly and easily.

Causes of Electrolux Dishwasher Error Codes

Electrolux dishwasher error codes can stem from many sources. Unblocking the drain system is one of the most popular causes. Communication errors between dishwasher components can also be at fault. Plus, a malfunctioning control board can trigger multiple codes.

Knowing the source of the issue is essential before taking action. These factors are known for creating Electrolux dishwasher error codes. Other causes like overflow, electrical malfunctions, and heating problems should also be considered. Examining all likely sources is necessary to identify the root of the problem.

Faulty drain systems, communication errors, and control board malfunctions commonly lead to Electrolux dishwasher error codes. Leaks in the detection system or water flow issues should also be examined during diagnosis. By understanding the causes, one can troubleshoot and fix the issue for a smooth dishwashing experience.

Common Electrolux Dishwasher Error Codes

Are you struggling with your Electrolux dishwasher ? If error codes are flashing on your appliance, it’s likely that some parts or systems are not functioning correctly. In this section, we’ll explore the meaning behind three common Electrolux dishwasher error codes: iC0, i20/i40/iFO, and #LOC . By understanding what these error codes indicate, you can identify the issue and find the best solution to get your dishwasher back up and running in no time.

iC0 Error Code: Communication Error

Your Electrolux dishwasher displaying ic0 ? It means that communication between the components is faulty. Could be from wiring, keypad or main control unit. Dishwashers use codes to talk to each other and do tasks. Communication failure? The ic0 error code appears on the display.

You can no longer use the dishwasher. Clean the drain filter, check wiring and circuit breakers. If these don’t work, call a professional. Reasons for the issue could be hardware, circuits or software. You need technical know-how to fix it.

Don’t call a plumber! Your Electrolux dishwasher can tell you where the blockage is with i20, i40, and iFO error codes.

i20, i40, iFO Error Codes: Drain System Blockage

When using Electrolux Dishwashers , watch out for i20, i40, and iFO error codes. These indicate a problem with the drain system, most likely due to a blockage. Act fast to avoid any effect on the dishwasher’s performance.

Start by checking the drain filter and clear away debris or food particles. Next, check the drain hose for kinks and bends. Also, use a multimeter to inspect the drain pump motor.

If the solenoid valve or pressure switch might be faulty, replace them. Clear away debris from the wash arms too. Use dishwasher cleaner to clear away buildup and keep drains clean. Pre-rinse dishes before starting a cycle to prevent blockages.

Unplug the dishwasher and check the parts before replacing the control board or drain pumps. This can help detect false error messages. Stacking dishes incorrectly can also cause clogs. Automated feedback detection and real-time self-diagnostics can identify and fix these issues. Lastly, you may need to replace the control board to solve problems .

#LOC Error Code: Control Board Issue

If your Electrolux dishwasher is showing #LOC , it’s likely a control board issue . The main control board looks after all electrical parts and activities. Check the wiring and connections to the board for any damage. If nothing is visible, you may need to replace the board. Check the part number and compatibility first. Instead, you could hire a qualified technician to find and fix the problem. Unplug the dishwasher for a few minutes – this may clear any internal errors in the control system and get it working normally again.

How to Fix Electrolux Dishwasher Error Codes

If you have an Electrolux dishwasher, you might encounter error codes that can disrupt your daily routine. In this section, we’ll show you how to fix Electrolux dishwasher error codes. We’ll cover everything from unplugging and inspecting/cleaning parts to replacing essential components such as the main control board or drain pump. Stay tuned to see how you can easily take care of malfunctioning sensors, leak detection system, and other common error codes.

Unplugging Dishwasher and Inspecting/Cleaning Parts

Safety is key when inspecting/cleaning an Electrolux dishwasher – unplug it first ! Switch off the power source, then disconnect the appliance’s plug from its socket. Inspect each part for damages and blockages with a brush or sponge. Note that other safety precautions should also be observed, like with rotors/sprayers that could cause cuts or burns.

After unplugging, remove the filters and ensure they are free from debris. Clean them with a soft brush and warm water. Cleanse clogged corners, focusing on areas around fixed items like sprayer arms. Examine the wash arm outlet (or turbine) by running a toothpick through its nozzles’ holes then running hot water through.

Reassemble all parts correctly, then reattach it back to its power source and switch it on. This inspection/cleaning may reveal other issues affecting its operation. It could be caused by particle buildup or broken components. Regardless of the cause, remember to stop dishwasher power supply before taking other actions.

Replacing Parts, such as the Main Control Board or Drain Pump

If your Electrolux dishwasher shows error codes, replacing important parts, like the main control board or drain pump , may help. Malfunctioning parts can cause these codes to show up. Here are 4 steps to replace them :

• Cut the power – Disconnect power to your dishwasher. Unplug from the wall or turn off the breaker.
• Take out the damaged part – Identify and remove the broken part. This may mean taking apart other parts, unplugging wires, and removing screws.
• Put in the new part – After taking out the broken part, install the new control board or drain pump as per the manufacturer’s instructions.
• Test – Put the parts together again before turning on the power. Run a test cycle. If there’s still an error, check if the installation was successful.

If you have trouble replacing parts, use your user manual or get professional help. Keep in mind that other issues may exist besides the control board and drain pump, which require a different solution. Look for issues specific to each error code. Also, if you changed the components but still see problems, contact a repair service provider as there may be further complex issues.

Replacing the main control board or drain pump might fix Electrolux dishwasher error codes.

Inspecting and Repairing Leak Detection System

It’s crucial to take action when there’s a leak in your dishwasher. Check all connections and hoses for leaks or improper fitting. If so, adjust or use sealants. Test the float switch by taking out all items and water, and lifting the float device. Consult your manual or call Electrolux if persistent problems occur.

Warranty may not cover leaks around door seals or wash arms, so address them right away . Monitor usage and seek help quickly to avoid bigger issues. Electrolux offers self-diagnostics and error codes to help.

Electrolux Dishwasher Self-Diagnostics and Error Codes

Are you tired of calling a technician every time your Electrolux dishwasher throws an error code? Well, worry no more! In this section, we will uncover the self-diagnostic and error codes system used in Electrolux dishwashers. From the dashboard display of error codes to the special test mode for all other codes and details, we’ve got you covered. No more confusion with flashing LED and end indicators in early models.

Dashboard Display of Error Codes

If you own an Electrolux dishwasher, you’ll be pleased to know it has a Dashboard Display . This display can show up to three letters and two digits. It’s designed to help you quickly and easily identify the problem.

We suggest you refer to our detailed table. It lists all the codes, explains what each code means, and provides instructions on how to solve the issue.

For example, if you see an iC0 error code, it means there’s been a communication error between various parts of your dishwasher. This may be due to faulty wiring or a disconnected circuit board. To fix the error, check all connections for loose parts and ensure they’re securely connected.

Most common error codes are in the table. However, not all errors will show up on the display. If you suspect a problem but don’t see any error codes, contact our customer service team for assistance.

Don’t ignore any issues with the dishwasher. It may lead to more significant complications that could damage other parts of your machine. So, if you’re having any problems, get help from us as soon as possible. Take action today and keep your dishwasher running smoothly with the help of our dashboard display of error codes.

Flashing LED and End Indicator in Early Models

Early Electrolux dishwashers had a unique feature. LED lights on the control panel would flash to show error codes. End indicator light would flash when the cycle was complete. Flash count & pauses meant different codes. Users had to use the user manual to decode them. That feature isn’t available in modern models.

The feature may not have been user-friendly. Users had to spend time decoding. Modern models display error codes directly on digital control panels. Makes troubleshooting easier.

Once, a customer called customer service. She thought the end indicator light flashing was an error code. They clarified and solved her confusion.

If you have an early model, pay attention to LED lights on control panel. With modern Electrolux dishwashers, error codes display directly on digital control panel – making troubleshooting easier.

Special Test Mode for All Other Codes and Details

To diagnose issues with their Electrolux dishwasher system, users must access the special test mode. This mode provides unique benefits to identify system errors accurately.

Hold the start button for 5 seconds to activate the sequence of commands and enter diagnostic mode. Once active, run the necessary tests to receive error codes.

It’s important to note that this mode should only be used by professionals or those familiar with working on dishwashers . Improper use may cause further damage or harm.

An example of successful use of this mode is one user who encountered an error code not listed in the manual. After entering the commands, they diagnosed a faulty sensor causing the issue. They replaced the sensor and the dishwasher was functional again.

The special test mode can be a valuable tool, if used carefully and competently .

Common Issues Related to Water Flow, Drainage, and Heating Up in Dishwashers

Dishwashers can have common issues with water flow, drainage, and heating. These are very inconvenient and may require expert help, especially if basic fixes don’t work. If you own an Electrolux dishwasher , certain error codes can point to specific problems like water leaking or heating elements not working.

Clogged filters, hoses, or pumps can cause water flow issues. The same goes for drainage problems which are often caused by damaged drain pumps or hoses. Additionally, heating elements may malfunction due to power supply or clogged filters. With Electrolux dishwasher error codes , you can diagnose the problem and do effective troubleshooting.

To avoid such problems, clean filters, hoses, and pumps regularly. Check the power supply too and make sure the dishwasher is loaded correctly. If the issues continue, it’s best to get professional help.

To sum up , it’s helpful to know Electrolux dishwasher error codes like i10 and i20 . They make it easier to find out what’s wrong with water supply and drainage. Plus, it saves cash. It’s also good to know why these errors happen, like a clogged filter system . In the end, Electrolux dishwasher error codes are essential for people who want their dishwasher to keep working well.

FAQs about Electrolux Dishwasher Error Codes

What does the electrolux error code ic0 indicate.

The Electrolux error code iC0 is a common error that indicates a communication error between the control board and the dishwasher, preventing the dishwasher from starting a load. To fix this error, you can unplug the dishwasher for 10 seconds, and if the code returns, replace the main control board.

Why does my Electrolux dishwasher throw an error code when I want to check the wash motor?

If your Electrolux dishwasher throws an error code when you want to check the wash motor, it may indicate a problem with the wash motor. To resolve this issue, you should inspect the wash motor for any signs of damage or malfunction. If you find any issues, you may need to replace the wash motor to get your dishwasher working properly again.

What does the Electrolux error code LOC mean?

The Electrolux error code LOC is the most common error on Electrolux dishwashers. This error indicates an issue with the door lock. If you receive this error code, check the door lock, latch, and strike for any signs of damage or malfunction. If you find any issues, replace the door lock to resolve the error.

What does the Electrolux error code i20 mean?

The Electrolux error code i20 indicates a draining problem. This error may be caused by a blockage in the drain line or a clogged drain pump. To fix this issue, unplug the dishwasher, inspect the drain line and drain pump for any blockages or clogs, and clean or replace the parts as necessary.

How can I check if my Electrolux dishwasher’s solenoid valve and temperature sensor work properly?

To check if your Electrolux dishwasher’s solenoid valve and temperature sensor work properly, you can perform a diagnostic test on your dishwasher. Ensure that the dishwasher is empty and follow the manufacturer’s instructions to activate the diagnostic test. The test will check all the dishwasher’s components, including the solenoid valve and temperature sensor, and report any issues that need attention.

What does the Electrolux error code i30 mean?

The Electrolux error code i30 indicates a leak. This error may be caused by a problem with the leak detection system or a damaged component in the wash tank. To resolve this issue, inspect the leak detection system and the wash tank for any signs of damage or malfunction, and repair or replace the parts as necessary.

SmartHomeBit Staff